Quick Answer: Is Cisco 2960 A Managed Switch?

How do I enable PoE on a Cisco 2960 switch?

Type “interface fastethernet1/2,” replacing the “fastethernet1/2” with the name of an interface in which you wish to enable PoE, and then tap the “Enter” key.

Then, while in interface configuration mode, type “power inline auto” and tap the “Enter” key.

Repeat this step for each interface in which PoE is required..

How much power does a Cisco 2960 switch use?

Power over Ethernet Ports The Catalyst 2960-24PC provides 24 10/100 PoE ports that can supply up to 15.4 W of power each, up to a maximum switch power output of 370 W. The Catalyst 2960 -24LT provides 24 10/100 ports, 8 of which are PoE ports that can supply up to 15.4 W of power each.

What is the default IP for Cisco 2960 switch?

The switch has a default IP address “10.0. 0.1” and a secondary IP address “10.0. 0.3”. 2 Enter a Hostname.

How much is a Cisco switch?

Table 1.Product Part NumberProduct DescriptionBase Price (Current)WS-C2960G-24TC-LCisco Catalyst 2960 24 10/100/1000, 4 T/Small Form-Factor Pluggable (SFP) LAN Base image$3,295WS-C2960G-48TC-LCisco Catalyst 2960 48 10/100/1000, 4 T/SFP LAN Base image$5,995

How much power does a Cisco switch use?

As noted, PoE+ alone consumes 1,440 watts of the total. The two switches use the remaining 364 watts, or around 182 watts each, comfortably within Cisco’s rated maximum of 246 watts per switch.

What is default IP of Cisco switch?

The switch uses the factory default IP address of 192.168. 1.254 by default. When the switch is using the factory default IP address, the System LED flashes continuously.

How do I console into a Cisco switch?

Make sure that you have correct console connection to Cisco Router or Switch. Connect the RJ45 jack of your console cable to the console port of your Cisco Router or Switch. Connect the other end to the Serial port of your computer.

How do I know if my Cisco switch has PoE?

Some ways to check if you have PoE on the network: On a Cisco switch, log in and enter show power inline and if it supports PoE, you should get output showing which ports are drawing power, a summary of configuration, etc. Any managed PoE switch should have a similar command.

How do I enable PoE on a Cisco switch?

How do I configure my CISCO Switch to properly power my PoE client?enable.configure terminal.interface interface-id.power inline {auto [max max-wattage] | never | static [max max-wattage]}end.show power inline [interface-id | module switch-number]copy running-config startup-config.

Is Cisco 2960 a PoE switch?

The Cisco Catalyst 2960 Series with PoE allows connectivity to Ethernet-powered devices, including Cisco IP phones, wireless access points, and video cameras. The Cisco Catalyst 2960-48PST-L can support 48 PoE ports with total PoE power output capacity at 370W.

Is PoE enabled by default?

Powered-Device Detection and Initial Power Allocation The switch detects a Cisco pre-standard or an IEEE-compliant powered device when the PoE-capable port is in the no-shutdown state, PoE is enabled (the default), and the connected device is not being powered by an AC adaptor.

What is a Cisco 2960?

A. The Catalyst 2960 Series PoE switches with intelligent services are ideally suited for small branch offices that can benefit from converged networks. The Catalyst 2960 Series provides enhanced security, scalable management, and unified network services for applications such as unified communications and mobility.